Adavnce Programmable Logic Controllers (PLC) Skills

Design – Simulation-Automation -Control
Advance Programmable Logic Controllers (PLC) Skills
For more info contact: Tel: 08133476558, 07085740887
Address: Opebi, Ikeja, Lagos State, Nigeria


MODULE 1
-PLC Jargon (FAQ)
-Fundamental of Control Logic
-Switch, Wire & Relay Logic
- Measuring & Sensing Devices
- Input Output Devices & Types
-Sensing Elements
- All about Fiber Optic and Sensors
-PLC Memory Unit, -Timer, -COUNTERS, -Advance Instruction, -Data and Control Instruction ,-Controller
-Code and Standard: IEC 61131-3, ASME/ANSI, DIN, ISA e.t.c

MODULE 2
-PLC Hardware’s and Panel wiring - Different types of Panels
- MCC – Panel overview - Power supply * CPU - I/O modules * Communication bus - Various ranges available in PLCs - Types of Inputs & outputs - Source and Sink Concept in PLC - Concept of flags - Scan cycle execution - Contactors, Relays - Power supply connection and communication port

-Practical class: Participants will design a PLC panel in full capacity

MODULE 3
-Common input and output devices
-Practical class: Participants will have on-hands skills on how to connect: 1. two wire sensors, 2. three wire sensors, 3.four wires sensor and 5. Five wires sensors to PLC and how to connect various output devices/final control elements, Ethernet, tcp e.t.c

MODULE 4
Input and output sensors:
Motors, Valves, Alarm/Light, Pumps as output devices
Configuration, Setup, operation, troubleshooting and management of:

Switches, relays, controllers, PID tuning, Fiber Optic Sensors, Proximity Sensors, Photoelectric Sensors, Displacement & Measurement Sensors.
Configuration and Setup of industrial Vision Systems. Digital and analog signal processing e.t.c
Level sensors and types (Point to point or continue monitoring)
Flow sensors and types (Point to point or continue monitoring)
Temperature sensors and types
Pressure sensors and types
e.t.c



MODULE 5
Digital and Analog, Programming In PLC, Practical Exposure to different PLC programming, Introduction to PLC programming software
- Addressing concepts (Syntax) for digital and analog
- Introduction to bit, byte & word concept
- Different between digital and analog programming
- Programming instructions arithmetic and logical
- Load /and /or/out / and Read / Write * MOVE block application

- Understanding PLC programming languages
- Compare / Add / Sub /And /Or - Blocks * Advanced instructions
- Leading edge / trailing edge instructions * File handling
- Timer Blocks programming * Comment functions
- Master control /set /reset function * Counter Block Programming
- Upload, download, Monitoring of programs
- Forcing I/P & O/P - Monitoring / Modifying data table values - PLC and Panel wiring
- Hands on experience on writing programs
- Case studies for conveyer, motors control, timer & counter applications etc.
- Troubleshooting and fault diagnostics of PLC
- Documenting the project
- Program assignments for real time applications
- PID programming
- Profibus configuration
-Practical: 100% practical class all through
-Commissioning of PLC panel
e.t.c
MODULE 6
Communication protocol
.Industrial networking - Serial, Ethernet and wireless communications. Propriety Or Open Protocol, Modbus RTU, Modbus ASCI, Modbus/TCP, Profibus, Fieldbus, Hart, DevicNet, Ethernet IP, Internet Wireless E.T.C

MODULE 7
Lab Work
Designing, programming and commissioning scenario:
- Digital input to digital output settings
- Digital input to analog output settings
- Analog input to digital output settings
- Analog input to analog output settings
- Designing PID controller

Lab work include panel wiring, design, programming, troubleshooting, and commissioning
e.t.c
Design – Simulation-Automation -Control
Advance Programmable Logic Controllers (PLC) Skills
For more info contact: Tel: 08133476558, 07085740887
Address: Opebi, Ikeja, Lagos State, Nigeria