Oil and gas training (piping & process design) in ph, 6

OIL AND GAS TRAINING IN PORT HARCOURT 2011
ELDEMUZ ENGINEERING CONSULTING IS A registered LOCAL CONTENT PARTNER with the federal government of Nigeria IN CAPACITY DEVELOPMENT for the oil and gas industry. We offer training to, consultant, engineers, managers, senior and junior staff in the oil and gas industry as well as fresh graduates and focused undergraduates. Our interest is for those pursuing excellence and improvement in their career. Our work force is made up of young Nigerian engineering graduates who have acquired software skills through the PTDF scheme. Our goal is to transfer knowledge at its best. The software’s we offer are used mostly by SHELL, MOBIL, SCHLUMBERGER, TOTAL, ELF, AGIP AND other major oil companies in Nigeria.
OIL AND GAS TRAINING
MODULE 1-PROCESS AND FACILITIES DESIGN
-Aspen HYSYS, PDMS, AUTOCAD.
MODULE 2--PIPING DESIGN AND PIPING STRESS ANALYSIS.
-PDMS,AUTOCAD,CAESARII,
MODULE 3--OIL FACILITIES DESIGN AND MANAGEMENT
-PDMS,AUTOCAD
MODULE 4--ENGINEERING DRAFTING, MODELING,AND ISOMETRIC DESIGN.
-AUTOCAD

OIL & GAS PROCESS MODELING WITH ASPEN HYSYS
The parameters we use for the design or construction of 0il ad gas facilities is gotten from process design. This information is part of what we call deliverables in
engineering design. HYSYS generates process deliverables like pressure, temperature, flow rate and other heat and mass properties which we use in the actual
plant design.
We have outlined about 10 modules involved in process modeling taking a guide from PTDF scheme and our over 5 years experience in process design and training
so as to simplify the understanding of the software. In addition the trainee will undergo a project on low station revamp, involving 8 oil and gas wells.
scope
•Introduction to HYSYS
• Propane Refrigeration loop
• Refrigerated Gas Plant
• NGL Fractionation Train
• Oil Characterization
• Gas Gathering
• Two-Stage Compression
• Acid Gas Sweetening with DEA
• Natural Gas Dehydration with TEG
• Reporting in Aspen HYSYS

HYSYS DYNAMIC SIMULATION
The dynamic simulation specifically handles EQUIPMENT sizing and process control
1. REVISION OF STEADY STATE
2. BASIC CONTROL THEORY
3. PRESSURE-FLOW RELATIONSHIP
4. TRANSITIONING FROM STEADY STATE TO DYNAMICS-MODYFYING THE STEADY STATE
5. SIZING UNIT OPERATIONS (DE-PROPANIZER COLUMN, SEPERATORS etc)
6. USING THE DYNAMICS ASSISTANT AND ACTIVATING THE DYNAMIC MODE
7. INSTALLING THE CONTROLLERS (PID)
8. SETTING UP STRIP CHARTS
9. RUNNING AND MONITORING DYNAMIC SIMULATION.
10. ADVANCED DYNAMICS

1.PLANT/PIPE DESIGN AND STRESS ANALYSIS (PDMS & CAESARII)
PDMS SCOPE
PDMS is the Vantage Plant Design 3D modeling application. It is a definitive 3D design and visualization solution.
It enables plant design personnel of various disciplines work actively together to eliminate structural interference, check safety and operational issues
during the design phase.
These ensure easy maintenance of facilities whilst taking cognizance of any human factors.
This course is designed to provide an understanding of PDMS for 3D Modeling and its application in Oil and Gas facilities. 3D modeling technology will be
introduced using PDMS.
The participant will be trained to appreciate the use of PDMS in developing Structural, Piping, Electrical and Instrumentation components as an introduction

to the necessary skills to optimize PDMS in the detailed Engineering of Oil and Gas facilities
1. In the Design module which is the graphical constructor we will cover the following discipline specific simulation applications.
A. Equipment DESIGN (vessels, pumps, heat exchanger, assemblies, air coolers)
B. Piping DESIGN INCLUDING explicit piping for piping engineers
C. Structural steelwork (column, beams, panels and plates, wall and floors)for civil
And structural engineers
D. ASL MODELLER (Access, stairs and ladder) for structural and civil engineers
E. Cable trays for electrical and electronics &instrument engineers
2. Production of MTO’s and piping general assembly
3. Conversion from PDMS Draft & Isodraft to AutoCAD format.
4. Customizing PDMS
5. Plant layout and drafting interpretation
6. Using ASME code
The training will be based on ASME B31.3 &B31.4 CODE.
At the end of the training, a PILOT project on modeling of an liquefied petroleum gas plant (COOKING GAS PLANT) will be carried out by the trainee.
CAESARII SCOPE
Caesar II is the world leading software in stress analysis
1. Basic functions of a pipe stress engineer, with emphasis on the relationship between the discipline and piping design.
2. Sources and solutions to piping stress related problems.
3. Pipe support standards.
4. Introduction to stress analysis
5. Setting pipe models for stress analysis
6.analysis on pumps.
7. Analysis
FULL PACKAGE AUTOCAD (2D, 3D&ISOMETRICS)
COURSE CONTENT-2D DRAFTING & 3D MODELLING
a. AutoCAD general
b. AutoCAD mechanical
c. AutoCAD PID, piping and instrumentation design.
D. AutoCAD structural /architectural.
AUTOCAD 2D DRAFTING
B. AUTOCAD MECHANICAL
1. DESIGN OF BASIC MECHANICAL COMPONENTS.(BOLTS,NUTS,FLANGES,E.T.C
2. INTERPRETATION OF METRIC AND IMPERIAL STANDARDS.AND DESIGN IMPLICATIONS.
3. Machine drawing
C. AUTOCAD PIPING.
1. PIPE DRAFTING AND DESIGN (PIPE ISOMETRICS, DOUBLE AND SINGLE LINE DRAFTING)
2.PIPING AND INSTRUMENTATION DIAGRAMS (P&ID),
4.PROCESS FLOW DIAGRAMS/SHEETS (PFD/PFS)
D.AUTOCAD CIVIL/STRUCTURAL/
1. House plan and elevations
2. BEAMS AND COLUMN DESIGN
3. SLAB DESIGN
AUTOCAD 3D MODELLING,
1. Introduction to 3d fundamentals-BASIC TOOLS (MODELING TOOL,SOLID EDITING,VIEWS,VISUAL STYLES ,3D MODIFY)
2. Modeling of structures (houses, PLATFORMS etc.)
3. Modeling of mechanical parts and components i.e. mechanical coupling
4. Modeling of piping components (elbows, tees, flange, reducer, valves, etc.) FOR 3D PIPING
5. DESIGN OF EQUIPMENTS (, pumps, pressure vessels, heat exchangers, e.tc)
6. Rendering 7. Project and assessment
ELIGIBILTY
B. THE CANDIDATE MUST HAVE A STRONG APPETITE FOR SELF DEVELOPMENT AND
LEARNING NEW SKILLS.
CLASS SIZE: 7 Persons/ Class.
DURATION-each of the programs takes 1 month
TIMING: 9am - 3pm, evening 5pm-8pm
Training date is slated as follows:
TRAINING STARTS, 6-30TH JUNE …2011
.REGISTRATION AND TERMS OF TRAINING:
Register BY SENDING US AN EMAIL TO
[email protected]
For details of the training fee call the
Following numbers. 08064919891, 08038812638
Venue;
EL-demuz engineering Resource Centre
First floor, 60 Aba Road,
By Craft Centre Bus Stop, near the footbridge
Port Harcourt.

Oil and gas training (piping & process design) in ph, 6 - 30th ,june 2011