Re: ETAP (Power System Analysis, Self Training for Fresh and Exp Electrical Engin

ETAP is a true 32-bit/64 bit program developed for the Microsoft® Windows® 2003/2008, XP, Vista, and 7 operating systems. It is fully interactive and allows you to make changes to the one-line diagram, run system studies, and graphically review study. It gives you the opportunity to explore the many features and capabilities of ETAP including Load Flow, Short-Circuit, and Underground Raceway Systems analysis.
ETAP is the leading software used by Electrical engineers for modeling of Electrical equipments in power plants, FPSOs, Transmission and Distribution stations to name a few. Being the leading software in the industry, knowledge of ETAP has become a SKILL for Electrical engineers of today. Comprehensive course notes will be provided with practical hands on examples.

PREREQUISITES:

Basic knowledge of Electrical principles, symbols and equipments.
I am willing to give the complete do-it-yourself manual out at a token for those who do not have the means of going for the Training (usually cost N200,000 ( you can make your findings too)).

In this training manual, you will Learn how to:
? Development of Single Line Diagrams, Libraries, Project Data Management, Cable Sizing, Templates
? Load Flow Analysis
? Short Circuit (IEC and ANSI)
? Motor Acceleration
? Transient Stability
? Protective Device Coordination and Selectivity
? Ground Grid Systems
? Underground Raceway Systems
? ArcFlash Analysis

? Other modules based on attendees request and time permitting
OBJECTIVES
At the end of the course, You should be able to :
? Build system single line diagrams using IEC standards and ANSI standards.
? Interpret and analyze Electrical study reports such as Load Flow report, Short Circuit report etc.
? Size protective devices; understand the principle of electrical protection and Transient Stability.
? Read and interpret TCC curves, Understand Arc Flash analysis, and recent IEEE and IEC regulations.


This is self training Manual.. But we can help as you proceed with the training.

For more Information, Contact [email protected] or 08109711539 (ope)

Please note that the training usually cost N200,000 and above but I am just giving out the do-it yourself manual at a token (N10,000( i might subsidized it though). Only serious People who wished to develop themselves and increase their chances in their career line should call or mail.

Etap Do it yourself manual consists of

Section 1: How to build and manipulate a one-line diagram

Section 2: How to set up and run a load flow study

Section 3: How to set up and run an unbalanced load flow study

Section 4: An introduction to ANSI and IEC short circuit studies

Section 5: How to set up an run arc flash analysis

Section 6: How to set up and run both static and dynamic motor acceleration studies

Section 7: A brief overview of a harmonic analysis of a system

Section 8: How to simulate and analyze system transients

Section 9: An overview of the basic operation of the Protective Device Coordination (Star) module

Section 10: An introduction to Optimal Power Flow analysis

Section 11: How to setup and run a reliability analysis

Section 12: An overview of the DC Load Flow module

Section 13: How to run a DC Short-Circuit study and make multiple study cases

Section 14: An introduction to Battery Sizing and Battery Discharge

Section 15: A brief overview of the Underground Raceway Systems module

Section 16: How to build and run studies on a Ground Grid Systems

Section 17: How to set up and build a Cable Pulling System

Section 18: How to set up and connect Panel Systems to existing networks

Section 19: A detailed explanation of the output report formats

Section 20: An overview of the libraries of ETAP

Please we won't go outside this course outline and they are with graphics to help you while studying

In each section, you will receive a training manual which you can follow (That is if you requested for a training). At the end of the self tutor, you will send your questions and it will be reviewed together.
For more enquires, please mail [email protected]

Dear friends.
It been long we updated the post on Etap. We are quite suprised to see people from Turkey , America and Poland mailing us and requesting for the Training manual and even for an online training. Its a pleasure but sadning that Nigerians do not know the value of this ETap training, even with the boost in the Power sector reforms now. It is an added advantage for power Engineers to go a lil ahead of their counterparts in skills. Act now. The manual is still available. Contact me. [email protected] or 08109711539