ETAP(Power System Analysis, Self Training for Fresh and Exp Electrical Engineers
ETAP is a true 32-bit/64 bit program developed for the Microsoft® Windows® 2003/2008, XP, Vista, and 7 operating systems. It is fully interactive and allows you to make changes to the one-line diagram, run system studies, and graphically review study. It gives you the opportunity to explore the many features and capabilities of ETAP including Load Flow, Short-Circuit, and Underground Raceway Systems analysis.
ETAP is the leading software used by Electrical engineers for modeling of Electrical equipments in power plants, FPSOs, Transmission and Distribution stations to name a few. Being the leading software in the industry, knowledge of ETAP has become a SKILL for Electrical engineers of today. Comprehensive course notes will be provided with practical hands on examples.
PREREQUISITES:
Basic knowledge of Electrical principles, symbols and equipments.
I am willing to give the complete do-it-yourself manual out at a token for those who do not have the means of going for the Training (usually cost N200,000 ( you can make your findings too)).
In this training manual, you will Learn how to:
♦ Development of Single Line Diagrams, Libraries, Project Data Management, Cable Sizing, Templates
♦ Load Flow Analysis
♦ Short Circuit (IEC and ANSI)
♦ Motor Acceleration
♦ Transient Stability
♦ Protective Device Coordination and Selectivity
♦ Ground Grid Systems
♦ Underground Raceway Systems
♦ ArcFlash Analysis
♦ Other modules based on attendees request and time permitting
OBJECTIVES
At the end of the course, You should be able to :
♦ Build system single line diagrams using IEC standards and ANSI standards.
♦ Interpret and analyze Electrical study reports such as Load Flow report, Short Circuit report etc.
♦ Size protective devices; understand the principle of electrical protection and Transient Stability.
♦ Read and interpret TCC curves, Understand Arc Flash analysis, and recent IEEE and IEC regulations.
For more Information, Contact [email protected] or 08109711539 (ope)
Please note that the training usually cost N200,000 and above but I am just giving out the do-it yourself manual at a token (N10,000( i might subsidized it though). Only serious People who wished to develop themselves and increase their chances in their career line should call or mail.
Re: ETAP(Power System Analysis, Self Training for Fresh and Exp Electrical Engineers
Etap Do it yourself manual consists of
Section 1: How to build and manipulate a one-line diagram
Section 2: How to set up and run a load flow study
Section 3: How to set up and run an unbalanced load flow study
Section 4: An introduction to ANSI and IEC short circuit studies
Section 5: How to set up an run arc flash analysis
Section 6: How to set up and run both static and dynamic motor acceleration studies
Section 7: A brief overview of a harmonic analysis of a system
Section 8: How to simulate and analyze system transients
Section 9: An overview of the basic operation of the Protective Device Coordination (Star) module
Section 10: An introduction to Optimal Power Flow analysis
Section 11: How to setup and run a reliability analysis
Section 12: An overview of the DC Load Flow module
Section 13: How to run a DC Short-Circuit study and make multiple study cases
Section 14: An introduction to Battery Sizing and Battery Discharge
Section 15: A brief overview of the Underground Raceway Systems module
Section 16: How to build and run studies on a Ground Grid Systems
Section 17: How to set up and build a Cable Pulling System
Section 18: How to set up and connect Panel Systems to existing networks
Section 19: A detailed explanation of the output report formats
Section 20: An overview of the libraries of ETAP
In each section, you will receive a training manual which you can follow (That is if you requested for a training). At the end of the self tutor, you will send your questions and it will be reviewed together.
For more enquires, please mail [email protected] or call 08109711539
Re: ETAP(Power System Analysis, Self Training for Fresh and Exp Electrical Engineers
ETAP is a true 32-bit/64 bit program developed for the Microsoft® Windows® 2003/2008, XP, Vista, and 7 operating systems. It is fully interactive and allows you to make changes to the one-line diagram, run system studies, and graphically review study. It gives you the opportunity to explore the many features and capabilities of ETAP including Load Flow, Short-Circuit, and Underground Raceway Systems analysis.
ETAP is the leading software used by Electrical engineers for modeling of Electrical equipments in power plants, FPSOs, Transmission and Distribution stations to name a few. Being the leading software in the industry, knowledge of ETAP has become a SKILL for Electrical engineers of today. Comprehensive course notes will be provided with practical hands on examples.
PREREQUISITES:
Basic knowledge of Electrical principles, symbols and equipments.
I am willing to give the complete do-it-yourself manual out at a token for those who do not have the means of going for the Training (usually cost N200,000 ( you can make your findings too)).
In this training manual, you will Learn how to:
♦ Development of Single Line Diagrams, Libraries, Project Data Management, Cable Sizing, Templates
♦ Load Flow Analysis
♦ Short Circuit (IEC and ANSI)
♦ Motor Acceleration
♦ Transient Stability
♦ Protective Device Coordination and Selectivity
♦ Ground Grid Systems
♦ Underground Raceway Systems
♦ ArcFlash Analysis
♦ Other modules based on attendees request and time permitting
OBJECTIVES
At the end of the course, You should be able to :
♦ Build system single line diagrams using IEC standards and ANSI standards.
♦ Interpret and analyze Electrical study reports such as Load Flow report, Short Circuit report etc.
♦ Size protective devices; understand the principle of electrical protection and Transient Stability.
♦ Read and interpret TCC curves, Understand Arc Flash analysis, and recent IEEE and IEC regulations.
For more Information, Contact [email protected] or 08109711539 (ope)
Please note that the training usually cost N200,000 and above but I am just giving out the do-it yourself manual at a token (N10,000( i might subsidized it though). Only serious People who wished to develop themselves and increase their chances in their career line should call or mail.